|Opcode/Instruction||Op/En||64/32-bit Mode||CPUID Feature Flag||Description|
F3 0F 6F /r
MOVDQU xmm1, xmm2/m128
|RM||V/V||SSE2||Move unaligned double quadword from xmm2/m128 to xmm1.|
F3 0F 7F /r
MOVDQU xmm2/m128, xmm1
|MR||V/V||SSE2||Move unaligned double quadword from xmm1 to xmm2/m128.|
VEX.128.F3.0F.WIG 6F /r
VMOVDQU xmm1, xmm2/m128
|RM||V/V||AVX||Move unaligned packed integer values from xmm2/mem to xmm1.|
VEX.128.F3.0F.WIG 7F /r
VMOVDQU xmm2/m128, xmm1
|MR||V/V||AVX||Move unaligned packed integer values from xmm1 to xmm2/mem.|
VEX.256.F3.0F.WIG 6F /r
VMOVDQU ymm1, ymm2/m256
|RM||V/V||AVX||Move unaligned packed integer values from ymm2/mem to ymm1.|
VEX.256.F3.0F.WIG 7F /r
VMOVDQU ymm2/m256, ymm1
|MR||V/V||AVX||Move unaligned packed integer values from ymm1 to ymm2/mem.|
|Op/En||Operand 1||Operand 2||Operand 3||Operand 4|
|RM||ModRM:reg (w)||ModRM:r/m (r)||NA||NA|
|MR||ModRM:r/m (w)||ModRM:reg (r)||NA||NA|
Moves 128 bits of packed integer values from the source operand (second operand) to the destination operand (first operand). This instruction can be used to load an XMM register from a 128-bit memory location, to store the contents of an XMM register into a 128-bit memory location, or to move data between two XMM registers. When the source or destination operand is a memory operand, the operand may be unaligned on a 16-byte boundary without causing a general-protection exception (#GP) to be generated.1
To move a double quadword to or from memory locations that are known to be aligned on 16-byte boundaries, use the MOVDQA instruction.
While executing in 16-bit addressing mode, a linear address for a 128-bit data access that overlaps the end of a 16-bit segment is not allowed and is defined as reserved behavior. A specific processor implementation may or may not generate a general-protection exception (#GP) in this situation, and the address that spans the end of the segment may or may not wrap around to the beginning of the segment.
In 64-bit mode, use of the REX.R prefix permits this instruction to access additional registers (XMM8-XMM15).
128-bit Legacy SSE version: Bits (VLMAX-1:128) of the corresponding YMM destination register remain unchanged.
When the source or destination operand is a memory operand, the operand may be unaligned to any alignment without causing a general-protection exception (#GP) to be generated
VEX.128 encoded version: Bits (VLMAX-1:128) of the destination YMM register are zeroed.
VEX.256 encoded version: Moves 256 bits of packed integer values from the source operand (second operand) to the destination operand (first operand). This instruction can be used to load a YMM register from a 256-bit memory
If alignment checking is enabled (CR0.AM = 1, RFLAGS.AC = 1, and CPL = 3), an alignment-check exception (#AC) may or may not be generated (depending on processor implementation) when the operand is not aligned on an 8-byte boundary.
location, to store the contents of a YMM register into a 256-bit memory location, or to move data between two YMM registers.
Note: In VEX-encoded versions, VEX.vvvv is reserved and must be 1111b otherwise instructions will #UD.
MOVDQU load and register copy (128-bit Legacy SSE version)
DEST[127:0] ← SRC[127:0] DEST[VLMAX-1:128] (Unmodified)
(V)MOVDQU 128-bit store-form versions
DEST[127:0] ← SRC[127:0]
VMOVDQU (VEX.128 encoded version)
DEST[127:0] ← SRC[127:0] DEST[VLMAX-1:128] ← 0
VMOVDQU (VEX.256 encoded version)
DEST[255:0] ← SRC[255:0]
void _mm_storeu_si128 ( __m128i *p, __m128i a)
__m128i _mm_loadu_si128 ( __m128i *p)
__m256i _mm256_loadu_si256 (__m256i * p);
_mm256_storeu_si256(_m256i *p, __m256i a);
See Exceptions Type 4; additionally
|#UD||If VEX.vvvv ≠ 1111B.|